10 Search Results

Industrial X-ray computed tomography (XCT) enables non-destructive inspection of additively manufactured (AM) parts, but high-resolution scanning requires long acquisition times and significant computational resources, limiting throughput in production environments. Super-resolution techniques can recover high-resolution information from low-resolution scans, but existing methods face a trade-off between 2D approaches that ignore inter-slice information and 3D methods that are computationally prohibitive for practical deployment. To address this trade-off, we propose a 2.5D deep learning-based super-resolution approach that uses seven neighbouring low-resolution slices to super-resolve the centre slice. This work evaluates the method on real XCT scans of steel AM parts, comparing reconstruction qualitymore » and flaw detection performance of 2D, 2.5D, and 3D ESRGAN-based super-resolution methods. Results demonstrate that 2.5D super-resolution significantly improves detection of small, process-induced flaws (e.g. porosity) compared to 2D methods, while avoiding the prohibitive computational burden of full 3D approaches. These findings provide initial evidence of 2.5D super-resolution as a practical, deployable solution for improving flaw detection in high-throughput industrial XCT inspection.« less

Tensile creep response and cavitation damage evolution in an additively manufactured Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt%) alloy with peak-aging and overaging treatments were investigated in the 300–400 ºC range. Microstructural heterogeneity and its response to heat treatment and subsequent creep deformation were studied to understand the interplay between cavity formation, creep lifetime and ductility. Increasing the applied stress activated the nucleation of more cavities, an experimental observation that is well described using the vacancy accumulation model. Cavities nucleated prematurely due to localized plasticity in the denuded zones that formed at/near melt-pool or grain boundaries. Microstructure/deformation heterogeneity with consequent evolution of stress triaxiality, especiallymore » at lower stresses, causes accelerated cavitation, thus producing low creep ductility (∼ 0.2–2.4 %), compared to (∼12–21 %) ductility of the alloy measured by regular tensile tests at equivalent temperatures. A constrained diffusional cavity growth mechanism with continuous cavity nucleation during creep is established as the dominant mechanism, implying that cavitation involves vacancy diffusion, yet its growth rate is dictated by the minimum creep rate. In conclusion, the ductility-limiting creep and cavitation mechanisms discussed here provide new insight into the creep behavior of 3D-printed metallic alloys.« less

Recent progress in sensing techniques and data analytics tools have significantly accelerated the development of Wire Arc Additive Manufacturing (WAAM) systems. This data-centric approach emphasizes leveraging sensor data available throughout the production process to optimize performance. Integration of extensive data analysis provides opportunities for improving precision, reducing waste, and enhancing the quality of produced parts. This method relies on AI/ML models and optimization techniques, which are developed using the data collected from various sources, including in-situ sensors, ex-situ imaging, and manufacturing process parameters. The quality and diversity of this data, along with the alignment between different data streams (achieved throughmore » spatiotemporal registration) are critical for the successful development of AI/ML and optimization models. In this work, we present a spatiotemporally registered dataset generated during the WAAM process of deposition of a rectangular block. The dataset includes a comprehensive description of the deposition process, process parameters, welding characteristics and acoustic data collected in-situ, and X-Ray Computed Tomography data of the build.« less

The concrete biological shield in light-water reactors is exposed to neutron and gamma irradiation, which deteriorates the concrete’s mechanical properties in the long term. To assess the irradiation-induced damage, predictive mechanical models are developed and used in parallel with the characterization of irradiated concrete samples. Realistic 3D simulation domains can drastically improve a model’s prediction. In this work, we utilized x-ray computed tomography (XCT) data of a concrete specimen to reconstruct its 3D microstructure. The XCT data shows low contrast between the concrete’s aggregates and cement paste, resulting in poor image segmentation when using traditional unsupervised techniques. To address thismore » issue, we developed and trained a 2.5D U-Net model on only 24 pre-labeled XCT layers to segment 651 layers of the XCT data. The overall F1-score of the model is approximately 96%. Then, we created a 3D finite element (FE) mesh based on the stack of segmented images. The FE model contains radiation-induced expansion, damage, and creep. The constitutive equations are adapted to each phase (aggregates and cement paste). Here, we simulated the effects of neutron irradiation in the concrete specimen as well as the specimen’s mechanical response to uniaxial compression. Finally, model validation was performed using experimental data on similar concrete specimens in the literature.« less

Direct reduction of iron ore using hydrogen plasma is being explored as a potential solution to decarbonize the iron and steel sector. The current state-of-the-art demonstrated reduction of hematite pellets via hydrogen plasma using Ar + 10% H₂ but had slow reduction kinetics, requiring 30 minutes of plasma exposure for complete reduction. Here we show that using hematite in a powder form, easily obtainable from beneficiated ore, results in 10× faster kinetics using plasma generated from Ar + 2% H₂ shielding gas compared to the current state-of-the art. Additionally, the increased kinetics using powders and a dilute hydrogen concentration canmore » enable the use of advanced manufacturing techniques like blown powder directed energy deposition using a plasma tungsten arc welding torch to manufacture near net shape components directly from the ore concentrates. This ore to part approach will also reduce the emissions associated with downstream processes like rolling, forging, and machining, thereby further aiding in the sectorial decarbonization efforts.« less

Creep deformation and cavitation were investigated at 300 ºC in both tension and compression for an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr (wt%) alloy in the as-fabricated state and after various aging treatments (aging at 300 °C/200 h or 350 °C/24 h and overaging at 400 °C/200 h). Creep mechanisms at 300 °C were determined by relating the measured creep response to corresponding microstructural and X-ray computed tomography observations. In compression, alloys in the as-fabricated and two aging conditions exhibited similarly high creep resistance. Overaging (400 °C/200 h) led to substantial coarsening of intragranular θ-Al2Cu precipitates and an expected drop in their Orowanmore » strengthening contribution. In tension, minimum strain rates comparable to those in compression were obtained at any given stress; however, upon accumulation of some plastic strain in the matrix, creep cavities started to form, leading to accelerated tertiary stage creep deformation and rupture. Cavitation occurred exclusively along melt pool boundaries due to locally enhanced diffusion enabled by (i) large grain-boundary area in adjacent fine-grained zones and (ii) localization of creep strain in nearby heat-affected zones. Although cavity growth was initially diffusion-controlled, its rate was determined by matrix creep rate, consistent with constrained cavity growth mechanisms. This study reveals how microstructural complexities induced by the additive manufacturing process affect the creep and cavitation behavior of Al-Cu-Mn-Zr alloys. The underlying creep and cavitation mechanisms uncovered in this study point to pathways that improve the high-temperature properties of additively manufactured alloys.« less

Microstructure control via additive manufacturing has enormous potential as manufacturers, materials scientists, and designers alike seek to exploit novel fabrication technologies to improve component performance. Recent works have demonstrated the feasibility of producing materials with controlled microstructures across various length scales. However, the experimental approach towards exploring the process-structure space can be laborious and costly. This is particularly true if also considering scan pattern optimization which is well suited for processes such as powder bed fusion electron beam melting. In this work we propose an approach for encoding additive manufacturing layer-wise thermal response signatures using self-supervised representation learning. Thermal simulationsmore » from a reduced order model are utilized to estimate the spatiotemporal response during printing. A machine learning framework, using video-transformers, is utilized to efficiently distill spatiotemporal patterns into a compact latent space representation. This latent state representation encodes the relevant physics which is then utilized to establish a data-driven process-structure model for an additively manufactured Ni-based superalloy. In conclusion, the proposed methodology could potentially be used towards in-situ process monitoring, scan pattern experimental design, and component qualification.« less

Accurate micromechanical simulation of polycrystalline materials requires a realistic digital representation of the grain scale microstructure. Here, this work demonstrates the use of a generative diffusion probabilistic model for synthesizing single phase polycrystalline realizations. The model performs well and is capable of producing realistic microstructures consisting of not just simple equiaxed structures but also structures exhibiting more complex spatial arrangements. Masked microstructure generation reveals that the model is context aware of morphological descriptors which may be encoded in the latent space. Training on more diverse data sets, with scaled up architectures, may enable development of future models capable of synthesizingmore » even more complex microstructural features.« less

Multiscale 3D characterization is widely used by materials scientists to further their understanding of the relationships between microscopic structure and macroscopic function. Scientific computed tomography (SCT) instruments are one of the most popular choices for 3D nondestructive characterization of materials at length scales ranging from the angstrom scale to the micron scale. These instruments typically have a source of radiation (such as electrons, X-rays, or neutrons) that interacts with the sample to be studied and a detector assembly to capture the result of this interaction (see Figure 1 ). A collection of such high-resolution measurements is made by reorienting themore » sample, which is mounted on a specially designed stage/holder after which reconstruction algorithms are used to produce the final 3D volume of interest. The specific choice of which instrument to use depends on the desired resolution and properties of the materials being imaged. Additionally, the end goal of SCT scans includes determining the morphology, chemical composition, or dynamic behavior of materials when subjected to external stimuli. In summary, SCT instruments are powerful tools that enable 3D characterization across multiple length scales and play a critical role in furthering the understanding of the structure–function relationships of different materials.« less

Layer dimensions are key parameters for as-fabricated tristructural-isotropic (TRISO) particle fuel as well as for post-irradiation examination of particle performance. Layer thicknesses are typically measured by optical microscopy of the particle cross section near mid-plane, while layer volumes are estimated with serial sectioning and microscopy. This method for measuring layer volumes is limited due to the resolution limit imposed by slice thickness and the effect of the polishing process on delicate irradiated particle microstructures. In this study, image processing software has been developed to segregate the three-dimensional (3D) TRISO particle images provided by x-ray computed tomography (XCT) into high-resolution volumetricmore » data for the kernel, all particle layers, and any internal voids introduced during irradiation. These data can be used to analyze key in-reactor behaviors of TRISO particles such as kernel swelling or buffer shrinkage, which are important inputs for fuel performance modeling.« less